****Show Us The inside of your Case!****

Are you using different fins for the dominators?

EDIT: Nvm, didnt realize you've only just ordered them

haha yea they only just came today :D i did say waiting on them.
Just finding it reallly hard to get a Bitfenix 6 Pin in red now in the UK.
Ordered one from america and it turned up this morning only to be a 24 pin atx.. gave me a full refund of it anyway which was good but now have another red atx cable
 
ORziL.jpg

My new system! I had to trim the plastic surround on the H100 fan in as it was against the mobo heatsink. Corsair 550D and MSI X79A-GD65 8D. Just fits now.
I have replaced all fans with Fractal Designs 120/140mm, on the H100 also.

My last case was a SilverStone FT01 which was probably nicer on the outside but this is so much better inside.
 
ORziL.jpg

My new system! I had to trim the plastic surround on the H100 fan in as it was against the mobo heatsink. Corsair 550D and MSI X79A-GD65 8D. Just fits now.
I have replaced all fans with Fractal Designs 120/140mm, on the H100 also.

My last case was a SilverStone FT01 which was probably nicer on the outside but this is so much better inside.

I want/need your gpu.
 
GarethH what fans you using on your H100? also 2 or 4 in push/pull? Blowing out of case i assume? Just interested as mine arrives tmrw with 4 akasa apache blacks

Edit

Nevermind, read the post, fractal fans.
 
GarethH what fans you using on your H100? also 2 or 4 in push/pull? Blowing out of case i assume? Just interested as mine arrives tmrw with 4 akasa apache blacks

Edit

Nevermind, read the post, fractal fans.

:) Yep just the two pulling air in. I became a fan (pun intended!) of positive pressure cases after running an FT01. No room on the 550D for push/pull (with my mobo anyway) unless you mount two of the fans externally.
 
:) Yep just the two pulling air in. I became a fan (pun intended!) of positive pressure cases after running an FT01. No room on the 550D for push/pull (with my mobo anyway) unless you mount two of the fans externally.

I got a carbide 500R with the top cut out that basically is made for a h100 to fit, and with push/pull, seen a few rigs with the same config il be going for, the old cooler i have has a silent typhoon 1850rpm on it, gonna pop that on the rear as an exhaust with the H100 set up to pull air in from above, over the rad, on to my 2 6950s, then the typhoon to exhaust it all, probably get a 2nd typhoon and pop it on the bottom infront of the psu whatever that cut out is called, and suck air in there also, should get a decent flow through and bring temps down a bit.
 
I got a carbide 500R with the top cut out that basically is made for a h100 to fit, and with push/pull, seen a few rigs with the same config il be going for, the old cooler i have has a silent typhoon 1850rpm on it, gonna pop that on the rear as an exhaust with the H100 set up to pull air in from above, over the rad, on to my 2 6950s, then the typhoon to exhaust it all, probably get a 2nd typhoon and pop it on the bottom infront of the psu whatever that cut out is called, and suck air in there also, should get a decent flow through and bring temps down a bit.

I am sorry to say but recently I build a pc for one of my mates and there is no space to go push/pull on the 500R if you mount the rad on top.
 
I am sorry to say but recently I build a pc for one of my mates and there is no space to go push/pull on the 500R if you mount the rad on top.

No biggie, il just put 2 on the H100, 1 on rear as exhaust and 1 on the floor infront of the PSU, get some air flowing through. I've been looking at the case and thought to myself it wouldnt work, cheers for the confirmation.

edit

after reading through loads of threads, There are people who have 4 fans fitted in push/pull on a H100 inside a 500R, so, im going to play later when the H100 arrives and get it up and running.
 
Last edited:
Maybe not the inside, but this is my current setup till I can stop the motherboard from shorting out inside the case.

20120528_181349.jpg

Im guessing your using the standoffs, so the board isn't resting on the motherboard tray?
 
I love yellow on black. Although I would have gone with a smaller res, the yellow just becomes a little overwhelming. I do like the detail on the fan screws :p
 
Back
Top Bottom