Associate
This mod is awesome. I love this because you push it even further than me 
ATX in Silverstone's ITX RVZ 03- ***full water and dual 240's ??
- Thread starter orbitalwalsh
- Start date
- Joined
- 1 Dec 2015
- Posts
- 18,512
@Plec about 4mm
Pushing and finish quality are two different things. Yours is polished, mines.... Like a scrap heap challenge
This mod is awesome. I love this because you push it even further than me
Pushing and finish quality are two different things. Yours is polished, mines.... Like a scrap heap challenge
Impressive. My R7 2700 clocked at only 4.05GHz peaked at that temperature and I'm using a 280mm AIO!
- Joined
- 1 Dec 2015
- Posts
- 18,512
Likewise , 2700 at 3.95gjz takes a lot of volts and custom loop with 360 rad ! Though can do 3700hz with ram was a blessing till some bios updates
haha yeah, big fan + big heatsink and direct airflow
also helps that PBO is disabled. so only 88w max draw
Associate
Thanks. Its 3D printed frame and tempered glass slides out from the back.
- Joined
- 1 Dec 2015
- Posts
- 18,512
honestly drooling over that one !
need to get a build log on here
couldn't help think, do i Try and go with some form of prettiness like yours for the front panel or go SCREW IT! MAXIMUM POWER! and get at 240mm Rad in the top section !!
Should've just gone with: http://www.lian-li.com/pc-05/
- Joined
- 1 Dec 2015
- Posts
- 18,512
My basket at Overclockers UK:
- 1 x Lian-Li PC-O5SW Mini-ITX Chassis - White= £364.99
- 1 x Lian-Li PC-O5SX Mini-ITX Chassis - Black= £299.99
- 1 x Lian-Li PC-O5X Mini-ITX Chassis - Black= £267.95
Total: £952.55 (includes shipping: £19.62)
white is an arm and a leg, then water unit is slightly more . Then adding £100 for SFX PSU ... ouch!
and if doing the same, using ITX version to house ATX board, SFX wouldn't fit , even with 90 degree orientation , inner space is too small . Thought least its 20 Liters but would have gone with Sliger cases
http://www.lian-li.com/pc-06s/ would have worked but HUGE!
more lego for @Plec
now the above picture!!! hightly currently have roughly 60mm to play with using current ram for Radiator... dimensions 48(H) x 134(L) x 9(W)mm
https://www.teamgroupinc.com/en/product/xtreem-ddr4
SFX is 63.5mm so anything 55mm is good. Seeing if XSPC have any spare ION Pump/Res combo's left over along with 20mm cooper rad . With silverstone 15mm fans it should be sorted ! Or reusing Silent Wing 3 to just offer a world full of airflow!
- Joined
- 1 Dec 2015
- Posts
- 18,512
yeah... JUST !
must remember to plug in BEFORE hand ! will take a closer snap shot and oduble check! haha
Soldato
Jesus wept! And I thought my In Win Chopin mod idea was insane and cramped!
Looking boss, boss!
Looking boss, boss!
- Joined
- 1 Dec 2015
- Posts
- 18,512
KICKER IS!!! PCIe cable is starting to get damaged from constant removal etc - believe i'll have to order another one
And GPU Wise
thanks
Its slowly getting there ! @Plec >>>>>
Plus side, Aorus logo on GPU is viable
- Joined
- 1 Dec 2015
- Posts
- 18,512
@Plec @tamzzy
90% installed , 50% complete
More Pictures and planning at the bottom of Post 2 <<<<< Click here for link
90% installed , 50% complete
More Pictures and planning at the bottom of Post 2 <<<<< Click here for link
Last edited:
- Joined
- 1 Dec 2015
- Posts
- 18,512
I'm playing catch up - but looking good, Orbi.
Is that the PSU's definite siting now? - Seems the best of both worlds and looks good in situ practicality wise (once covered).
Shame about the PCIe riser cable but it looks like it's taken its fair share of abuse this past week.
You are going to have to incorporate, permanently, a bit of Lego into this build - even if it's only pseudo propping up the GPU. As mentioned - i'm sure i've seen a build with a Lego Figure (Iron Man/Hulk would be cool for your kids) propping up back end of GPU.
Have you reached a decision re panel/plexi - and rad?
Also, what's the plan/news for the new front fascia?
*Did you remove backplate of GPU for more space - or do you think it's required?