** LIAN-LI PC-O11 DYNAMIC EDITION - A NEW ENTHUSIAST PRICE/PERFORMANCE CONTENDER ARRIVES **

Still a work in progress but here's mine so far - need to add in braided cables and tidy it up a bit. Apologies for the low quality pic and glare :)

20180824_153225.jpg
 
Can anyone confirm if an Alphacool XT45 360 rad will fit in the side location without modding the case or the IO cables in any way? If not then will a HW GTS360 fit (again with no need to mod the case)?
 
Been looking at this case.

I was thinking of having 3 x ML 120's doing intake from side, vert mounting the GPU (2080ti wind force) and then NZXT Kraken X62 radiator at the top doing exhaust. No fans at bottom. Any issues with this setup?
 
I’ve had a Kraken x62 mounted at the top. It will fit and work but a fair bit is covered by the mounting panel so not completely allowing air flow to flow unrestricted. Would be better with a 360 rad mounted to the top.

Considering another top panel
slots over covering the whole lot it’s not ideal for a 280 rad I feel.

Just my view.
 
NightElf said:
I’ve had a Kraken x62 mounted at the top. It will fit and work but a fair bit is covered by the mounting panel so not completely allowing air flow to flow unrestricted. Would be better with a 360 rad mounted to the top.

Considering another top panel
slots over covering the whole lot it’s not ideal for a 280 rad I feel.

Just my view.
Click to expand...

Would it be possible for you to take some pics? Are you planning to side mount it instead?
 
@Silent_Scone can you tell me how your fans are setup? Push/pull.

I really want this case but I'd just be getting a AIO for the CPU which seems like a waste. I'm a bit nervous about taking about the RTX. Even then, I've never done WC so anything past AIO's, I'd be uncomfortable with.

What do you think of this config. 3xside intakes. Kraken X62 AOI top mount exhaust. Vert GPU (per benefits shown by Gamernexus review). It's basically their config but the AIO and top exhaust should give me a cooler GPU temp and over all temps.
 
Robert896r1 said:
@Silent_Scone can you tell me how your fans are setup? Push/pull.

I really want this case but I'd just be getting a AIO for the CPU which seems like a waste. I'm a bit nervous about taking about the RTX. Even then, I've never done WC so anything past AIO's, I'd be uncomfortable with.

What do you think of this config. 3xside intakes. Kraken X62 AOI top mount exhaust. Vert GPU (per benefits shown by Gamernexus review). It's basically their config but the AIO and top exhaust should give me a cooler GPU temp and over all temps.
Click to expand...


I went with what was practical for the setup I wanted, rather than best temp scenario. Both rads are exhausting, with three fans as intake at the top. Water temps in worst case scenario for gaming are around 35C which is higher than what I'm used to on bigger builds, but still more than reasonable. No push pull on this setup.
 
Fatpizza said:
Does anyone know if the Cablemod vertical GPU bracket works with fans at the bottom of the case?
Click to expand...

Looking at the pictures, there doesn't seem much room underneath it at all so I can't see how it would be possible to fit fans. The SSD brackets only just fit in the pic below.

CM-VPB-2-DK-R-2.jpg
 
Anyone with a hybrid gpu able to check if there's enough length in the tubing to put the rad at the forward top slot? Not a deal breaker but would rather not have it sucking hot air off the mobo vrm.

Of if someone could put a tape measure to it roughly where the hybrid gpu tubes come out?
 
Can this and the air version support an itx motherboard. Lianli website says eatx, atx and matx but on here it says itx for the dynamic but doesn't say it for the air version.
 
I'm thinking of trying to sell my Phanteks Evolv as the air flow just isn't good enough and i was wondering if the O11 Dynamic would be an improvement? I know there is the Air version but i just dont like the look of it.
 
You must log in or register to reply here.
Back
Top Bottom