My biggest build! the lian li DK-03

well she is up and running, not done bios yet going to do that tomorrow. but omg I love her!!!!!!! however i used pink dye, it looks like milkshake in the system hahaha
 
yeah sorry it was just a tester to see if it all works, the core temp sits at 60-69.. I think the cpu maybe faulty. I've purchased another motherboard just to test, hopefully that will indicate if it is the motherboard or the cpu it's self that is hot. as for the pink. it looks like damn strawberry milkshake at the minute. it needs to be a lot darker, but I will sort that out once I sort the motherboard/cpu problem out. then once the new mobo arrives I need to sort out the NZXT hue fans, they seem to not light up. Anyone know how these work?
 
Found out that the Ryzen 1800x and 1700x have a 20c raised sensor temp, so the temp is wrong, (it is for OC reasons)
so far i found the NXZT has a terrible sticking solution, so have replaced them with double sided tape. and they seem to be a lot more grippy, (for those using aluminium use double sided tape on top of the one supplied.)
my motherboard is dead but it was damaged via delivery so i suspect it was damaged there. new one hopefully arrives tomorrow and the old has been called back for it to be looked at.
Not had a chance to work the NXZT RGB fans as of yet. also changing the tubing tomorrow.
 
ok it has had a change, I've sent back some items to overclockers (my own fault on the cd drive) and the seagate fire SSHD does not work on any of my pc's. so getting a replacement. however the biggest improvement is the pipe work, i've changed it today. it looks a lot smarter and more dynamic. it's half full now but i will take a pic of it in moment. tomorrow the new mobo arrives and the old leaves, fingers crossed.
 
Here is the new pipe work, I personally think it looks smarter and sleeker, also i have shortened the loop a little due to it being more direct then it was before. As you can see I have removed the elbow fitting on the radiator, This gives it a little bit of a straight line (bar the few bends to get it spot on) few of my friends said they thought the pipe work was meh,(on the last build of this) and to be honest so did I.
the block it's self has been angled better too. with both fittings facing the same way with bends near on matching from the pipe. The new mobo arrives tomorrow and the old one went earlier today.
also I broken the NZXT pin fitting (check last pic) anyone know where I can get a replacement from?)














 
Hi guys sorry been very busy! Well thanks guys yeah braking up via the gpu would be a future idea, next on my list is to redo the tubing again in the future to a fatter tube size, yeah not going over the gpu would have been real nice however the pipe is only 90cm long so I am only limited to a small amount.
at the minute I got it like the joker effects
 
Hi all sorry been really busy! so far this is my beautiful girl. She needs another NZXT fan on the right to make the 4th some cable management needs sorting bar that, she is looking good for me :)





























 
Thorhax said:
How much was the total cost if you don't mind answering?
Click to expand...
cost me a lot more then I should have spent lol
GinG said:
That looks great...however to me the desk looks rather awkward and very uncomfortable. For the price you don't get a great deal of room, I would very much struggle to ever use that.
Click to expand...
i'm 6ft 2in chair raised to max height lots of room for me ;) i think for giants no this is not great lol but ofr me the little guy i have leg room galore, p.s i want a foot raise so i cn put me feet up lol
Minibiker said:
The RAM looks so nice in this build, also the Dual monitor setup is great..
Click to expand...
i changed it yesterday, but now the Gskill program has gone to put yet again because i have Cam software plus the Aorus software running. At the moment as i spoeak i don't think £400-£500 for the g skill trident was worth it, i have sent back 5 times due to complications to the software.
 
so a year and a half later, next on this subject, i got a new little item getting the one for the card to my mobo aswell made by lian li.
so what are my next plans? well to upgrade!
so by this time from now in 6 months the plan should be RTX 2080TI
2 4k monitors made by predator and curved, love the curve life i got at the minute.
thinking of getting a custom built feature on my left hand side for my pc, i have a nice gap that i feel could be made to better use.
pipe work will be changed to fatter pipes. (so new custom fish fittings for me)


 
You must log in or register to reply here.
Back
Top Bottom