* Official Ubiquiti Discussion Thread *

ChrisD. · 11 Dec 2017 at 14:16

The cloud controller works now after applying it again, but if I try and go to my Vigor 130 address it's hitting the USG interface instead.

the-evaluator · 11 Dec 2017 at 14:25

I think you've made a mistake on your JSON.

You've set the IP address of eth0 to 192.168.2.1/24 which is the default management address of the 130. Try changing eth0 to 192.168.2.2/24 and try again.

ChrisD. · 11 Dec 2017 at 14:35

Ah, yes of course. Doh!

the-evaluator · 11 Dec 2017 at 14:38

I may have done the exact same thing myself in the past

ChrisD. · 11 Dec 2017 at 14:39

It's all working now, including cloud access. Thanks for your help.

Now to play with Smart Queues.

DIABLO · 11 Dec 2017 at 14:56

Can’t have Smart queues and DPI at the same time, I believe you said you were using DPI in a previous post.

As it stands it’s the same deal with new Intrusion detection feature that is in the new Betas.

ChrisD. · 11 Dec 2017 at 15:02

Really? Smart queues is enabled and DPI is still showing data.

Simon42 · 11 Dec 2017 at 15:52

It's not updating DPI data without hardware offload and Smart Queues disables that hence the general loss of throughput as well

ChrisD. · 11 Dec 2017 at 15:54

Seems a bit daft that you can enable both in the GUI, there should be something to say that one will disable the other.

DIABLO · 11 Dec 2017 at 16:41

I think a hover over tooltip says it, don’t quote me on it though.

Simon42 · 12 Dec 2017 at 10:08

An alpha firmware for the USG has just been released that allows DPI without hardware offload so it's coming.

However for me the bandwidth limitations without hardware offload are too much (even with the pro)

the-evaluator · 12 Dec 2017 at 10:09

I've just installed the alpha firmware, will do some testing later.

ChrisD. · 12 Dec 2017 at 10:10

Has anyone in here had any Cloud Key failures? I'm reading a lot of people with issues on the Ubiquiti forums and I'm tempted to spin up a container on my QNAP to do the job and return the cloud key.

shine · 12 Dec 2017 at 10:18

I've had my cloud key since the beginning of the year - no issues so far.

Simon42 · 12 Dec 2017 at 10:21

No problems here, but there was an earlier revision so not sure if the failures are more common in that. Even though I have a couple of dedicated servers at home I like the cloud key as it just keeps everything separate but still in house.

ChrisD. · 12 Dec 2017 at 10:37

I seem to be getting a bit more throughput with the USG than I did with pfSense. Only about 4Mb or so, but still nice. Then again I did have Snort running before.

DIABLO · 12 Dec 2017 at 14:13

the-evaluator said:
I've just installed the alpha firmware, will do some testing later.

Got a link to the firmware page? Last I can see is 4.4.14

the-evaluator · 12 Dec 2017 at 14:20

https://community.ubnt.com/t5/UniFi...5dev-available-for-testing/m-p/2170396#M14154

bledd · 12 Dec 2017 at 14:25

The Alpha/Beta shouldn't be posted outside of their forums really..

Especially ones with 'dev' in the name, always the possibility of bricking!

DIABLO · 12 Dec 2017 at 14:38

the-evaluator said:
https://community.ubnt.com/t5/UniFi...5dev-available-for-testing/m-p/2170396#M14154
.

Cheers, you can remove the direct links if you want to as I can access the beta forums

*** Official Ubiquiti Discussion Thread ***

* Official Ubiquiti Discussion Thread *