Project Whurple - White/Purple Watercooled Build - Changes to 3d printer build!!

Vince said:
Right RAM, lets talk RAM!!!




So i was playing about that set with purple dots and me messing about have been painted probably 5 times. The plan was the little triangles at the bottom and a line across the bottom that is raised purple but with the current masking tape situation that is not happening. So do I:

  1. Wait for the tape
  2. Go just white
  3. One half of the RAM White, the other half purple? Whurple!
  4. Pancake
Click to expand...
I noticed the riser cable!! I also noticed the wrinkles so kept quiet...

I mean probably just wait for the tape but you could still do opposite strips on each side of the ram? Or would that be too much? See if the tape turns up before your other china stuff maybe??
 
clifbel said:
I noticed the riser cable!! I also noticed the wrinkles so kept quiet...

I mean probably just wait for the tape but you could still do opposite strips on each side of the ram? Or would that be too much? See if the tape turns up before your other china stuff maybe??
Click to expand...

It's fine :(, I think I will have to get a 3d printed part sort of cover like device to hide that monstrosity, I also need some sticky "stuff" for the memory as its become not so sticky during the process. It will be all good by the time I throw it all together when it is done.
 
mrbell1984 said:
You got a 3D printer? If not someone might make one and send ya it. Not sure how you would mount it there though!
Click to expand...

I do not have a 3d printer. I know people who do but I can't be sending them 3 million parts all the time. And this is how:



Make a little thingy to fit in the hole.
 
Vince said:
I do not have a 3d printer. I know people who do but I can't be sending them 3 million parts all the time. And this is how:



Make a little thingy to fit in the hole.
Click to expand...

Will you make the 3D printed thingy purple as well? Or will you do some funky paint job on it??
 
clifbel said:
Will you make the 3D printed thingy purple as well? Or will you do some funky paint job on it??
Click to expand...

So far I am at a stop, I am hoping the post man gives me some new toys to play with tomorrow, the observant will notice some toys for another project in one of the photos :)
 
Vince said:
So far I am at a stop, I am hoping the post man gives me some new toys to play with tomorrow, the observant will notice some toys for another project in one of the photos :)
Click to expand...
god forbid all postmen/postwomen stop delivering
mail must be a corona virus risk to them surely
resistors?
to alter led colour?
 
clifbel said:
Are you able to adjust the fan colours to what you want in the meantime? And is this CPU Epoxy thing in another thread?? Sounds fun!
Click to expand...

I'll be honest I havent tried yet. I'm going to need more rgb led knowledge but id rather wait until the other controller gets here to see what we are working with first. I do know that they have 4 pins and 3 of them correspond to r,g,b.

The cpu thing is an epoxy pen holder with a cpu at the base. Im going to make a wooden base for it and the leds will be wired up and shine below the cpu to light up the epoxy. Just plug the base in using a micro usb.

There is a thread. When I update it I'll post a link in here.
 
Last edited:
clifbel said:
Are you able to adjust the fan colours to what you want in the meantime? And is this CPU Epoxy thing in another thread?? Sounds fun!
Click to expand...
Don't know lot about it but was guessing
Colour to be created by different voltage
To red, green and blue
Which is what I thought the resistors were for
Perhaps even potentiometer would work?
Though know little beyond splicing stuff that uses 5v or 12v into my
Molex connectors
But assuming Vince knows more than me about electronics :)
 
You must log in or register to reply here.
Back
Top Bottom