*** Official Ubiquiti Discussion Thread ***
- Thread starter RoyMi6
- Start date
Where is your controller running? You can do this - https://help.ubnt.com/hc/en-us/arti...Adoption-Methods-for-Remote-UniFi-Controllers
But if there's not a correct config in your controller then it will upload bad data.
But if there's not a correct config in your controller then it will upload bad data.
SSH into the kit using what was your original log in to the controller (unless you changed it) then do the following
Code:
mca-cli
set-inform http://IP.OF.YOUR.CONTROLLER:8080/informIt should now show in your new controller but you're not done, click the adopt button and then go back to your SSH session and do the following (again)
Code:
mca-cli
set-inform http://IP.OF.YOUR.CONTROLLER:8080/informNow the adoption will "complete" and the SSH session will close itself upon successful adoption.
Install it again, restore your config backup file that you took.
Soldato
- Joined
- 24 Sep 2015
- Posts
- 3,972
Yep. It was an absolute doddle, took about 10 minutes from start to finish.
I bought the cheapest of the cheap SSL certs from ssls.com. I have a guide somewhere at home that I cna dig out next week if you need it.
I bought the cheapest of the cheap SSL certs from ssls.com. I have a guide somewhere at home that I cna dig out next week if you need it.
I'm looking at https://letsencrypt.org/getting-started/ for a free one, I'll give it a go and shout if I get stuck. Thanks! 
Soldato
- Joined
- 24 Sep 2015
- Posts
- 3,972
I had a few issues with Lets Encrypt so rather than waste too much time I spent £15 or so on a 3 year certificate.
I'm looking at https://letsencrypt.org/getting-started/ for a free one, I'll give it a go and shout if I get stuck. Thanks!
Nightmare. UBNT forums have scripts that are supposed to work but they don’t.
UBNT are looking at a gui option to add this.
Current setup I have is BT ADSL with a Homehub, then connected to a 24port switch and also have a couple of Ubiquiti AP's for wireless along with the Homehub's wireless (all on separate channels). I have a USG arriving later today. What do i need to do to get it set up correctly?
I've just started searching and it seems like I'll need to change some settings on the Homehub and USG in order to the USG to access the internet so it looks in the right place. I'll also be turning off the wireless in the Homehub as I dont think it's needed, my Ubiquiti AP's should cover the whole house well enough. Are they any recommended guides/tips for setting this up with a BT homehub or must-do's before i start? I've already got on my todo list to make a note of all of the port forwarding rules i've set up and static assigned IP's for several devices on the Homehub to copy across to the USG.
Thanks.
I've just started searching and it seems like I'll need to change some settings on the Homehub and USG in order to the USG to access the internet so it looks in the right place. I'll also be turning off the wireless in the Homehub as I dont think it's needed, my Ubiquiti AP's should cover the whole house well enough. Are they any recommended guides/tips for setting this up with a BT homehub or must-do's before i start? I've already got on my todo list to make a note of all of the port forwarding rules i've set up and static assigned IP's for several devices on the Homehub to copy across to the USG.
Thanks.
Best case scenario would be to get a modem and then use pppoe on the USG.
As you are the USG should get internet from DHCP, just DMZ the IP the USG takes so it has "full fat" internet access and isn't NAT'd. Double NAT isn't a problem as such but some services like gaming and VOIP can be quite difficult to fault find if you have 2 NAT tables to work through.
Ok cheers, i'll look into that. So the setup in that case is modem->USG->router, so the modem simply replaces the Homehub in the chain? So with a new modem, there is obviously no IP setup for the incoming internet, and you use the PPPoe and login details from BT? Any idea if you can pick one up from a high st store anywhere?
Ah, so DMZ is simply setting the IP of the USG in the Homehub settings so that no rules/restrictions are placed on it, so that from the point of view of the USG, the Homehub is invisible? That shouldnt be too hard!