Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
Thanks, it now unlocked. Do I need to input username / password on BT Openreach Modem WAN for FTTC? As I have Netgear DGND3700v2 as I will using this router for wifi.
Last edited:
Post your FTTC line stats & unlocking info
- Thread starter Locky
- Start date
No. Configure PPPoE on the DGND3700v2.
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
Thanks for this.
Associate
- Joined
- 9 Sep 2008
- Posts
- 1,377
Just got my first router with integrated VDSL modem, first time I've had access to stats -
Think I'm about 320 metres from the cabinet.
Code:
root@SRX110> show interfaces pt-1/0/0 extensive
Physical interface: pt-1/0/0, Enabled, Physical link is Up
Interface index: 148, SNMP ifIndex: 532, Generation: 151
Type: PTM, Link-level type: Ethernet, MTU: 1518, VDSL mode, Speed: VDSL2
Device flags : Present Running
CoS queues : 8 supported, 8 maximum usable queues
Hold-times : Up 0 ms, Down 0 ms
Current address: 54:e0:32:d2:5c:a0
Last flapped : 2014-01-31 23:14:16 GMT (18:31:43 ago)
Statistics last cleared: Never
Traffic statistics:
Input bytes : 132 0 bps
Output bytes : 14227217 0 bps
Input packets: 2 0 pps
Output packets: 62763 0 pps
Input errors:
Errors: 0, Drops: 0, Policed discards: 0, L3 incompletes: 0, L2 channel errors: 789, L2 mismatch timeouts: 0, Resource errors: 0
Output errors:
Carrier transitions: 1, Errors: 0, Drops: 0, Aged packets: 0, MTU errors: 0, Resource errors: 0
Egress queues: 8 supported, 4 in use
Queue counters: Queued packets Transmitted packets Dropped packets
0 best-effort 3944553 3944551 2
1 expedited-fo 0 0 0
2 assured-forw 0 0 0
3 network-cont 9466 9466 0
Queue number: Mapped forwarding classes
0 best-effort
1 expedited-forwarding
2 assured-forwarding
3 network-control
VDSL alarms : None
VDSL defects : None
VDSL media: Seconds Count State
LOF 0 0 OK
LOS 0 0 OK
LOM 0 0 OK
LOP 0 0 OK
LOCDI 0 0 OK
LOCDNI 0 0 OK
VDSL status:
Modem status : Showtime (Profile-17a)
VDSL profile : Auto Annex B
Last fail code: None
Subfunction : 0x00
Seconds in showtime : 244
VDSL Chipset Information: VTU-R VTU-C
Vendor Country : 0xb5 0xb5
Vendor ID : BDCM IFTN
Vendor Specific: 0x9385 0xb203
VDSL Statistics: VTU-R VTU-C
Attenuation (dB) : 0.0 0.0
Capacity used (%) : 0 0
Noise margin (dB) : 8.5 9.5
Output power (dBm) : 13.5 4.5
Interleave Fast Interleave Fast
Bit rate (kbps) : 0 79999 0 20000
CRC : 0 0 0 0
FEC : 0 0 0 0
HEC : 0 0 0 0
Packet Forwarding Engine configuration:
Destination slot: 0 (0x00)
CoS information:
Direction : Output
CoS transmit queue Bandwidth Buffer Priority Limit
% bps % usec
0 best-effort 95 19000000 95 0 low none
3 network-control 5 1000000 5 0 low none
Logical interface pt-1/0/0.0 (Index 80) (SNMP ifIndex 533) (Generation 145)
Flags: SNMP-Traps VLAN-Tag [ 0x8100.101 ] Encapsulation: PPP-over-Ethernet
Traffic statistics:
Input bytes : 132
Output bytes : 148
Input packets: 2
Output packets: 2
Local statistics:
Input bytes : 132
Output bytes : 148
Input packets: 2
Output packets: 2
Transit statistics:
Input bytes : 0 0 bps
Output bytes : 0 0 bps
Input packets: 0 0 pps
Output packets: 0 0 pps
Security: Zone: untrust
Allowed host-inbound traffic : bootp dns dhcp finger ftp tftp ident-reset http https ike netconf ping reverse-telnet reverse-ssh rlogin rpm rsh snmp snmp-trap ssh
telnet traceroute xnm-clear-text xnm-ssl lsping ntp sip r2cp
Flow Statistics :
Flow Input statistics :
Self packets : 0
ICMP packets : 0
VPN packets : 0
Multicast packets : 0
Bytes permitted by policy : 0
Connections established : 0
Flow Output statistics:
Multicast packets : 0
Bytes permitted by policy : 0
Flow error statistics (Packets dropped due to):
Address spoofing: 0
Authentication failed: 0
Incoming NAT errors: 0
Invalid zone received packet: 0
Multiple user authentications: 0
Multiple incoming NAT: 0
No parent for a gate: 0
No one interested in self packets: 0
No minor session: 0
No more sessions: 0
No NAT gate: 0
No route present: 0
No SA for incoming SPI: 0
No tunnel found: 0
No session for a gate: 0
No zone or NULL zone binding 0
Policy denied: 0
Security association not active: 0
TCP sequence number out of window: 0
Syn-attack protection: 0
User authentication errors: 0
Logical interface pt-1/0/0.32767 (Index 82) (SNMP ifIndex 539) (Generation 147)
Flags: SNMP-Traps VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2
Traffic statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Local statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Transit statistics:
Input bytes : 0 0 bps
Output bytes : 0 0 bps
Input packets: 0 0 pps
Output packets: 0 0 pps
Security: Zone: Null
Flow Statistics :
Flow Input statistics :
Self packets : 0
ICMP packets : 0
VPN packets : 0
Multicast packets : 0
Bytes permitted by policy : 0
Connections established : 0
Flow Output statistics:
Multicast packets : 0
Bytes permitted by policy : 0
Flow error statistics (Packets dropped due to):
Address spoofing: 0
Authentication failed: 0
Incoming NAT errors: 0
Invalid zone received packet: 0
Multiple user authentications: 0
Multiple incoming NAT: 0
No parent for a gate: 0
No one interested in self packets: 0
No minor session: 0
No more sessions: 0
No NAT gate: 0
No route present: 0
No SA for incoming SPI: 0
No tunnel found: 0
No session for a gate: 0
No zone or NULL zone binding 0
Policy denied: 0
Security association not active: 0
TCP sequence number out of window: 0
Syn-attack protection: 0
User authentication errors: 0Think I'm about 320 metres from the cabinet.
what router is that?
Associate
- Joined
- 9 Sep 2008
- Posts
- 1,377
Juniper SRX110H-VA, found an almost new one going cheap on eBay(normally far too expensive for me). It only has 100Mb ports but that doesn't matter since it is used to feed the WAN to a wireless access point which has an integrated gigabit switch.
Just had my sky fibre connection go live today, syncing at 40/10 but getting 18/10 on various speedtest sites.
My stats are below...
Broadband Link Downstream Upstream
Connection Speed 39998 kbps 9999 kbps
Line Attenuation 7.8 dB 0.0 dB
Noise Margin 25.9 dB 31.31 dB
Any idea what sort of speed i should be able to get when DLM finishes its initial run?
My stats are below...
Broadband Link Downstream Upstream
Connection Speed 39998 kbps 9999 kbps
Line Attenuation 7.8 dB 0.0 dB
Noise Margin 25.9 dB 31.31 dB
Any idea what sort of speed i should be able to get when DLM finishes its initial run?
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
That's pretty poor speed (sound like up to 24Mbps ADSL2+) as for DLM won't be kicked in the day after new install. Are u using wireless? Try it with ethernet direct from your sky router to your pc or laptop.
There is nothing wrong with the connection from you to the cab very good stats. As you say there is a problem with throughput.
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
He probably using wireless with poor speed throughput.
Yup, using the WiFi from the sky hub :/ Ordered a 15m cat5e cable long enough to reach the PC, should be here Tuesday courtesy of the fine chaps at OcUK 
The shop being so close is the only thing I miss about living in Stoke on Trent, now I'm back in Southport I have to rely on my lovely free postage, the local pc component stores are woeful in comparison.... Says a lot when Screwfix sell cat5e cheaper than them
The shop being so close is the only thing I miss about living in Stoke on Trent, now I'm back in Southport I have to rely on my lovely free postage, the local pc component stores are woeful in comparison.... Says a lot when Screwfix sell cat5e cheaper than them 
In recent days, after a long period of a settled sync and SNR, I noticed my attainable rate had increased again and, at my current sync, I had an SNR of around 8 down and 7.5 up. That lasted for a good day so I decided to run a longer graph and see what was happening.
This is what I got:-
If there was a fault, I would have expected a lower value fluctuation instead of flicking between my established values and those that are higher?
Any insights?
This is what I got:-
If there was a fault, I would have expected a lower value fluctuation instead of flicking between my established values and those that are higher?
Any insights?
Last edited:
Soldato
My line stats, i have an Sky Superhub Black
Is there a way to unlock these ?
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
Are mine looking good or bad? As this is my first time unlocked HG612 Modem
http://postimg.org/image/7px9hjx2b/full/
http://postimg.org/image/dpl0l7hur/full/
http://postimg.org/image/7px9hjx2b/full/
http://postimg.org/image/dpl0l7hur/full/
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
How to get this stats? I would like to see mine too
Soldato
That looks terrible. Max sync rate, attainable circa 108mb/38mb, no errors reported, stable SNR.
Absolutely awful! The cabinet must be all the way outside your front door.
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
Really? I thought that stats looking very good. Are you trying to flob me off?
Soldato
Soldato
- Joined
- 22 Mar 2009
- Posts
- 5,721
I would raise a fault with your ISP/OR immediately.
What a load of rubbish talk from you. The line is look excellent. The ISP say these are very good line stat. So, I will ignore your reply.
According to speedtest, there is nothing wrong with the line.
Soldato
What a load of rubbish talk from you. The line is look excellent.
According to speedtest, there is nothing wrong with the line.
You're achieving max speeds and your ping is 11ms that is far too high...
EDIT: Have you not sensed the sarcasm yet?
